WiFi Floodlight Security Camera

Quick User Guide for the YESKAMO WiFi Floodlight Security Camera and its 2-in-1 NVR Recorder with Monitor (abbreviated as "Monitor").

Safety Caution

1. Wireless only means no any cables between camera and monitor base, but the whole camera system need to be plugged into power socket for power supply.
2. Please use the included power supply with the product to prevent damage to the product.
3. Please avoid any avoidable obstacles and electromagnetic product between camera and monitor for better signal.
4. All man-made damages are outside the scope of free warranty.

Product Introduction

WiFi Floodlight Security Camera

1. Microphone — Pick up audio.
2. 4pcs Floodlight — Will turn on automatically in the darkness when PIR sensor triggered.
3. 4pcs IR led — IR leds will automatically switch on at darkness for night vision.
4. Speaker — Transmit sound.
5. 3dBi Antenna — Receives wifi signal from monitor.
6. Weatherproof IP66 Housing — Working temperature: -20°C/-4°F to 60°C/140°F.
7. IR Cut Filter — Auto switch day/night.
8. PIR Sensor — Detect objects in the monitoring area.
9. TF Card Slot — Insert TF Card for video storage. (Max support 128G TF Card, TF card must be FAT32 format. Camera in kit doesn't support TF card function.)
10. Reset button — Press and hold reset button about 5-10 seconds to restore camera to factory setting.
11. 2-Axis Mounting Bracket — Adjust installation angle and vandal-proof inside cable, 360° all-round swiveling and 90° up-down adjusting.
12. Power-in Port — Connect with provided 12V 1A plug for power supply.
13. RJ45 Ethernet port
    • A: Pair / match code camera with monitor when camera lose connection.
    • B: Hard wire camera with monitor or router to get stable signal (DO NOT CUT IT OFF).

2-in-1 NVR Recorder with Monitor

1. Screen Button — Press to turn on/off the screen. (Please keep the screen off when you out, make it more durable.)
2. Antenna — Release strong wireless signal from Monitor.
3. 3.5'' Internal Hard Disk — Save video from NVR system.
4. Power Input — Connect the provided 12V 3A adapter for power supply.
5. USB port — For USB mouse control, USB flash drive port for video footage backup and system upgrading.
6. WAN Port
   • A: Connect to router with Ethernet cable for remote viewing.
   • B: When you add new camera to YESKAMO Monitor, or your camera lose system online. Connect on with monitor, you need this Ethernet port to pair camera with Monitor.
7. HDMI video output — Connect monitor to HDMI input port of your TV/monitor (HDMI cable not included).
8. Audio-out — Insert with the Speaker.

Connection Instruction

1. Plug camera to power socket with provided 12V 1A adapter.
2. Plug monitor to power socket with provided 12V 3A adapter.
3. Plug mouse to Monitor.
4. Optional: if you want extra TV/monitor, connect monitor to it with HDMI cable (Not included).
5. Use Ethernet cable to connect the WAN port of Monitor to LAN port of router, make the system online if you want to remotely view the cameras on phone app. (Skip it if you only want to view local videos on monitor.)

• User name: admin
• Password: No password (Default password is no password, let it blank and click "Ok" to login the camera system).

Remotely View the Cameras on the Phone

1) Make sure the NVR monitor is ONLINE status

Connect the WAN port of NVR monitor to LAN port of router with Ethernet cable, then the NVR monitor will be ONLINE. Right click the mouse to enter main menu > Fast Network > Cloud (P2P) > ONLINE.

2) Download free app

Search free APP "YESKAMO" or "EseeCloud" in App Store or Google Play. The phone app will be updated sometimes; if your phone app menu is different from the menu in user manual, please contact us to get the latest user manual.

For a detailed walkthrough of registering and logging in, see the EseeCloud App User Guide.

3) Create an account and log in phone app

Register an account with your email address / phone number and password. A verification code will be send via text.

4) Add Cloud ID

• A: Enter APP > click "+" in the right top corner or center of the phone > Scan the Cloud ID.
• B: Enter APP > click "+" in the right top corner or center of the phone > "Other ways to add" > Input "Device Cloud ID" > the default password is no password, click "Add" and "Complete" to finish.

Where to find the Cloud ID:

• A: Right click the mouse to enter main menu > Fast network > Cloud (P2P).
• B: Right bottom corner of the monitor.
• C: The label on the NVR/Monitor.

• Name of device: Customize the system name (such as home, office, room...).
• User Name: Default is admin (the same as your NVR monitor).
• Password: Default is no password, leave it blank/empty (same as your NVR monitor system).

5) Remotely view camera via phone

Double tap the screen, and you can view camera anywhere anytime.

Two-Way Audio Communication

Turn on the speaker button at top right corner of phone app and you can hear the audio from camera side.

Tap the microphone button to enter chat screen, then press and hold the microphone button and you can talkback to camera side. Tap the hang up button to return preview screen.

How to Enable the Siren Alarm from Camera Side

There are 4 types of PIR activated alert available — Buzzer, Email, phone app notification and IPC Alarm. You can customize the PIR activated alerts based on your requirement.

• Buzzer — Monitor will beep when motion is detected.
• Email alert — You will receive an email alert (refer to "full manual user").
• Phone app notification — You will get a phone app notification push.
• IPC Alarm — You will hear siren alarm from camera side.

Take IPC alarm as an example, it sounds a siren alarm from camera side when PIR is activated. Right click mouse to enter main menu > System Setup > Channel Setup > Video Detection > select channel and click "Enable" > check/enable "IPC Alarm" > click "Apply" to save the setting.

How to Manually Turn Off the Floodlight at Night

This floodlight camera has a built in PIR sensor and floodlights. The floodlight will automatically switch on at night when detect any suspicious activities and offer true color videos. But you can customize the IR-Cut mode to turn off the floodlight as below steps:

Before customizing the IR-Cut mode for a selected channel, please double click the channel you want set, to enter full screen mode. Right click mouse to enter main menu > Color Adjust > IR-Cut mode: Infrared, Daylight, Night, Full Color, Smart Mode.

How to Add a New Camera to YESKAMO NVR with Monitor

The cameras are paired with monitor before packed and it will auto pair with monitor after you plug whole camera system to power socket. But if the camera lost connection with monitor accidentally or you want to add a new camera to this kit, please pair / match code the camera with monitor as below steps:

1. Take the camera near monitor.
2. Plug camera to power outlet via the provided 12V 1A power adapter.
3. Use Ethernet cable (RJ45) to connect camera with monitor, the WAN indicator light at back panel of Monitor will turn on.

4. Right click mouse to enter main menu > Video Manage. The upper box shows information of camera, and lower box shows channel information of monitor.
5. If the channel status at lower box shows "IPC disconnect", "connect fail", "different segment"..., select that channel with mouse, then click "delete" and the status of that channel will be "No video source".
6. Click "Search" in the upper box, new IP address will pop up in minute and then click "match code".
7. The camera will be connecting with monitor and "Wifi add" interface will pop up.
8. Click "Exit" until the camera's IP address pops up for that channel. (The IP address will be 172.20.14.xx.)
9. The picture of camera will be shown on monitor and the status of that channel will be "connect success" on video manage interface.
10. Then you can disconnect the Ethernet cable and install the camera at anywhere you want. (Camera should be installed within the monitor's wifi range, and connect the Ethernet cable back to router with monitor if need remote view.)

How to Install Hard Drive for Monitor

The monitor need a hard drive to save the record. If you bought a monitor without hard drive or you want to replace the pre-install hard drive with larger memory, please install it by yourself as the following instruction:

1. Remove the screws on the back panel of monitor.
2. Take the back panel off from monitor.
3. Holding the hard drive and the monitor panel, gently and line up four holes on the hard drive with the monitor panel.
4. Screw the provided screws into the holes between hard drive and back panel by a Phillips screw driver.
5. Connect the SATA power and data cables from the monitor to the corresponding ports on your HDD.
6. Slide the monitor panel back on and fix the panel with Phillips screws as picture.

Technical Support

• Website: www.yeskamo.com
• Email: [email protected] (for US), [email protected] (for UK)
• US Cell: +1 830 745 5888
• UK Cell: +44 20 3807 4763

You can also browse our Help Center for more troubleshooting and FAQ.